Epilog Fusion Pro Laser Machines
Introducing the new Epilog Fusion Pro. 5G acceleration and 165 IPS engraving speeds provide the fastest engraving in the industry. And the IRIS™ Camera Positioning system allows you to precisely place your artwork on screen in seconds.
- Fusion Pro 32: 32” x 20” (812 x 508 mm) work area
- Fusion Pro 48: 48” x 36” (1219 x 914 mm) work area
- Wattages:
- CO2: 50, 60, 75, or 120 watts
- Fiber: 30 or 50 watts
- Dual: Configure your laser with both CO2 and Fiber sources
Features: Benefits of Epilog’s Fusion Pro Laser System
The Fusion Pro laser engraving and cutting machines from Epilog are our top-of-the-line laser systems and combine a large work area with the latest technological features, including:
Høyhastighetsgravering over de største arbeidsområdene
The Fusion Pro’s 165 IPS engraving speed and 5G acceleration combine to provide the fastest engraving in the industry.
IRIS™ Camera Positioning
Overhead cameras provide an accurate picture of the working area for accurate artwork placement, and a camera at the lens allows the system to find preprinted registration marks.
Touch Screen at the Laser
Select between jobs, change settings, and more right from the easy-to-use touch screen interface right at the laser. Rerun jobs at the touch of a button.
Utformet og produsert i USA
Proudly designed, engineered, and manufactured in our Golden, CO headquarters at the base of the Rocky Mountains.
Kommuniser med laseren på tvers av virksomheten
The Fusion Pro features built-in Ethernet, USB, and a new wireless connection for more options for networking your laser.
SAFEGUARD™ Features
Keep the mechanics of your laser machine cleaner than ever before with side bellow enclosures, a fully covered x-axis assembly, and covered lens assembly.
Air Assist and Compressor
The air assist removes heat and combustible gases from the cutting surface for a cleaner cut. A built-in air compressor provides air directly to the work surface.
Table Choices
On the Fusion Pro 48 mix and match your table across the bed with optional slat and gridded cutting tables.
Radiance™ Beam Enhancing Optics
No additional, expensive lens package needed for the highest resolution engraving across the entire table.
CO2 Waveguide-laserrør av Epilog
Rørdesign i kun metall gir høyere strålekvalitet og lengre levetid, samt lavere oppladningskostnader.
1 GB Memory in the Machine
Improve job management and data integrity with 1GB of RAM in both Fusion Pro systems. Save your most run jobs right at the laser.
Long-Life Steel Bearing
A dual block design provides the most rigidity and reduced vibration without the inevitable wobble and replacement of plastic bearings.
Tilbehør
Alternativ med to kilder: CO2 og fiber
Are you looking for the material versatility of a CO2 laser in addition to the direct metal etching of a fiber laser? Add on the dual source option to your Fusion Pro by choosing both a CO2 laser (50, 60, or 75 watts) and a fiber laser (30 or 50 watts) to work with a wider range of materials.
Rim-Style Rotary Attachment
Available for the Fusion Pro, the Rim-Style rotary attachment adds the ability to engrave bottles, glasses, flashlights, or any other cylindrical item. The Fusion Pro rotary attachment is as easy to setup as placing your product on the rotary, raising or lowering the scissor lift to level the engraving area, and printing to the laser.
Rotor til spindel med 3 kjever
The Fusion Pro 3-Jaw Chuck mechanically clamps a cylinder or oddly-shaped, non-cylindrical item in place as the laser engraves. It is the perfect accessory when your engraving requires extremely precise positioning on your cylindrical items.
PhotoLaser Plus-programvare
PhotoLaser Plus takes photo engraving with your Epilog Fusion Series laser to the next level by easily processing photos for engraving on all types of materials. Epilog Laser has partnered with CADLink to bring you the industry’s best photo processing software: PhotoLaser Plus. The easy-to-use software interface and powerful photo processing tools allow you to create the highest-quality photo engravings in the industry.
Valgfrie linser
1.5” Lens: Highest-Resolution Engraving
Although the standard 2” lens provides amazing detail, our 1.5” lens assembly has been designed for the highest-resolution engraving and etching of extremely small fonts.
4.0” Lens: Cutting Thicker Materials and Inside Deep Areas
The 4” lens produces a focused beam over a longer vertical distance, which makes it ideal when engraving within a recessed area of a product, such as inside a bowl or plate. The lens is also used for cutting through very thick materials.
Cone Lens: Deep cutting with the Laser
The cone design pushes the stream from the Air Assist directly down through the cut, rather than over the surface of the engraving material. This provides even better reduction of laser flare-ups and better edge quality.
Cutting Pin Table
For tappeplaten følger det med flyttbare tapper som kan plasseres hvor som helst i platens rutenett med hull som står én tomme (25,4 mm) fra hverandre. Med de flyttbare tappene kan brukeren også løfte og støtte skjærematerialet på steder der laseren ikke skal skjære, slik at du kan eliminere baksidegjenspeiling. Du kan også plassere tapper på bordet for å støtte deler som normalt ville vært utenfor skjæremønsteret. En praktisk overflateplate som kan fjernes, gjør det enkelt å rengjøre små partikler uten at du må fjerne tappeplaten.
Epilog Fusion Pro Technical Specifications
| Fusion Pro 32 | Fusion Pro 48 | |
|---|---|---|
| Arbeidsområde | 32” x 20” (812 x 508 mm) |
48” x 36” (1219 x 914 mm) |
| Maximum Z-Depth | 12.25” (311 mm) | 12.25” (311 mm) |
| Laser Tube Wattage |
CO2 - 50, 60, 75, or 120 watt
Fiber - 30 or 50 watt
|
|
| Programvare | Epilog Laser Software Suite: Laser Dashboard & Epilog Job Manager | |
| Minne | Multiple files up to 1 GB. Engrave any file size. | |
| Driftsmoduser | Optimized Raster, Vector, and Combined Modes | |
| Bevegelseskontroll | High-speed, continuous-loop, brushless DC servo motors using rotary encoding technology for precise positioning | |
| Lagre for X-aksen | Ground & polished stainless steel, Teflon-coated, self-lubricating bearings. Dual blocks on X-axis for greater rigidity | |
| Reimer | Advanced B-Style Kevlar belts (x-axis) and steel cord (y-axis) | |
| Oppløsning | Fully-flexible and user-controlled from 75 – 1200 dpi | |
| Speed and Power | Computer-controlled in .001 increments up to 100% | |
| Grensesnitt for utskrift | 10Base-T Ethernet, USB, or Wireless connection. Windows 7/8/10 compatible | |
| Størrelse (B x D x H) | 54.6” x 34.2” x 42" 1387 x 869 x 1067 mm |
70.6” x 51.3" x 42.75" 1794 x 1304 x 1086 mm Pedestal removed: 34” H (863 mm) |
| Vekt | 400 lbs (182 kg) | 500 lbs (227 kg) |
| Electrical | 240 volts, 50 or 60 Hz, single phase | |
| Ventilasjon | 650 CFM (1104 m3/hr) external exhaust to the outside or internal filtration unit required. Three output ports, 4” (102 mm) diameter. | |
| Exhaust Ports | One output port 4” (102 mm) |
Two output ports 4” (102 mm) |
| Vacuum Table Port | Additional port for dedicated exhaust through table, 4” (102 mm) | |
| Sikkerhet | Class 2 Laser Product – 1 mW CW Maximum 600 – 700 nm | |
Epilog Fusion Pro Material Compatibility
| Gravere | Skjære | |
|---|---|---|
| Tre | x | x |
| Akryl | x | x |
| Stoff | x | x |
| Glass | x | |
| Metall med belegg | x | |
| Keramikk | x | |
| Delrin | x | x |
| Tøy | x | x |
| Lær | x | x |
| Marmor | x | |
| Matt bord | x | x |
| Melamin | x | x |
| Papir | x | x |
| Mylar | x | x |
| Trykkbord | x | x |
| Gummi | x | x |
| Finér | x | x |
| Glassfiber | x | x |
| Malt metall | x | |
| Flis | x | |
| Plast | x | x |
| Kork | x | x |
| Corian | x | x |
| Anodisert aluminium | x | |
| Rustfritt stål | * | |
| Messing | * | |
| Titan | * | |
| Bart metall | * | |
| * CO2-laserere vil markere bart metall når det er belagt med en metallmerkeløsning. For mer informasjon, besøk vår side for merking av metall med laser. | ||
| Har du et materiale du ønsker at vi skal teste? Vårt Bruksområdeteam hjelper deg med glede. | ||
Be om mer informasjon
Motta en brosjyre og prøver gratis
Motta brosjyrer og prøver, og få mer informasjon fra oss eller den lokale forhandleren.
2019 © Epilog Laser. Med enerett. Personvern | Finn distributører | Nettstedkart